ASTM Section 8:2011

ASTM Book of Standards – Section 8 – Plastics (Vols. 08.01-08.04)

2010 sections include 695 standards.This section includes Volumes 08.01 through 08.04.

  • Volume 08.01 Plastics (I): D 256-D 3159
  • Volume 08.02 Plastics (II): D 3222-D 5083
  • Volume 08.03 Plastics (III): D 5117–latest
  • Volume 08.04 Plastic Pipe and Building Products

Ordering information and availability

Available in both printed and PDF file edition.

ANSI/NETA MTS-2011

Standard for Maintenance Testing Specifications for Electric Power Distribution Equipment and Systems, 2011 Edition

Published by IETA (International Electrical Testing Association) in 2011, has 273 pages.

The NETA Maintenance Testing Specifications was developed for use by those responsible for the continued operation of existing electrical systems and equipment to guide them in specifying and performing the necessary tests to ensure that these systems and apparatus perform satisfactorily, minimizing downtime and maximizing life expectancy.

Ordering information and availability

Available in both printed and PDF file edition.

ANSI/AWWA D100-11

Welded Steel Tanks for Water Storage

This standard was published by AWWA (American Water Works Association) in July 2011. It has 236 pages.

The purpose of this standard is to provide minimum requirements for the design, construction, inspection, and testing of new welded carbon steel tanks for the storage of water at atmospheric pressure.

Ordering information and availability

Available in both printed and PDF file edition.

ASTM A370-11

Standard Test Methods and Definitions for Mechanical Testing of Steel Products

This standard was published by ASME in May 2011.

These test methods cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.

Ordering information and availability

Available in both printed and PDF file edition.

API Spec 5CT

Specification for Casing and Tubing, 9th Edition

This standard was published by API (American Petroleum Institute) in July 2011. It has 281 pages.

This Standard specifies the technical delivery conditions for steel pipes (casing, tubing and pup joints), coupling stock, coupling material and accessory material and establishes requirements for three Product Specification Levels (PSL-1, PSL-2, PSL-3). The requirements for PSL-1 are the basis of this Standard. The requirements that define different levels of standard technical requirements for PSL-2 and PSL-3, for all Grades except H-40, L-80 9Cr and C110, are contained in Annex H.

This Standard can also be applied to tubulars with connections not covered by API standards.

This Standard is not applicable to threading requirements.

This Standard is based on the Eighth edition of API Spec 5CT.

Ordering information and availability

Available in both printed and PDF file edition.

AISC 325-11A

Steel Construction Manual, 14th Edition

Was published in 2011 by American Institute of Steel Construction.
This Manual is the fourteenth major update of the AISC Steel Construction Manual, which was first published in 1927. Replacing the 13th Edition Manual, the 14th Edition Manual contains several updates and revisions, including the new HP18 and HP16 series, updated connection tables based on increased bolt shear strength values, revised single-plate and extended single-plate connection design procedures, enhanced prying action procedure, and a revised bracket plate design procedure.
The following specifications, codes and standards are printed in Part 16 of this Manual:
  • 2010 Specification for Structural Steel Buildings, including the new Chapter N on QC and QA, expanded composite design provisions, and improved slip-critical connection provisions
  • 2009 RCSC Specification for Structural Joints Using High-Strength Bolts
  • 2010 AISC Code of Standard Practice for Steel Buildings and Bridges

Ordering information and availability

Available only in printed hardcover edition.

CAN/CSA M421-11

Use of Electricity in Mines

Edition: 4th, 86 pages
Published by Canadian Standards Association (CAN) in April 2011
ISBN: 9781554915330
This Standard establishes minimum requirements for electrical work and electrical equipment operating, or intended to operate, in mines. Note: Users should be aware that federal, provincial, and territorial legislation can impose additional requirements.

1.2 Application

This Standard is intended to be used with the requirements of the Canadian Electrical Code, Part or local regulatory amendment thereto, unless such requirements are modified by this Standard. Note: Adherence to the Canadian Electrical Code, Part I, normally addresses the minimum electrical safety requirements for mining-related fixed buildings, structures, and premises located on the surface, as these are no different from other industrial facilities. Such facilities could include processing plants, camps, offices, and drys. However, specific applications can exist within or on such buildings, structures, or premises that warrant the application of this Standard, e.g., the following equipment operating at voltages exceeding 150 V to ground: (a) mobile equipment fed by portable power cables; (b) movable equipment fed by portable power cables where the ground-fault voltage and ground potential rise relative to the surrounding earth or structures cannot be limited to 100 V; and (c) quick-connect couplers that are not mechanically interlocked with a load-break-rated disconnect switch.

1.3 Application to non-mining structures

This Standard does not apply to tunnels, aqueducts, conduits, or excavations for civil construction purposes. However, where mines incorporate such structures, this Standard applies.

1.4 Clause numbering system

This Standard is divided into seven clauses, numbered from 1 to 7. Clauses are further divided into subclauses (e.g., Clause 4.3). There can be up to five levels of subclauses (e.g., Clause 4.3.3.3.1). Multiple items, designated by lowercase letters in parentheses (e.g., (a), (b), (c)) can be enumerated in a list. If an item requires further listing, subsidiary items are identified by lowercase Roman numerals in parentheses (e.g., (i), (ii), (iii)). Items in a further list under these subsidiary items are identified by an Arabic numeral in parentheses (e.g., (1), (2), (3)). Note: For further information see CSA-SDP-3.2.

1.5 Inclusive lists and selective lists

The use of the conjunction “and” between two or more items in a sentence or list conveys an inclusive relationship, i.e., all of the items or conditions in the list are included in the criteria (i.e., all items present or conditions satisfied). The use of the conjunction “or” between two or more items in a sentence or list conveys a selective relationship, i.e., at least one of the items or conditions in the list is included in the criteria (i.e., a selective choice).

1.6 Terminology

In CSA Standards, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application.

Ordering information and availability

Available in both printed and PDF file edition.

IEEE C2-2012-HB

NESC Handbook: A Discussion of the National Electrical Safety Code, 7th Edition

This 7th edition was published by IEEE in August 2011.

The 2012 NESC Handbook, Seventh Edition, edited by Allen Clapp, is an essential companion to the Code. It gives users insight into what lies behind the NESC’s rules and how to apply them. The Handbook was developed for use at many levels in the electric and communication industries, including those involved in system design, construction, maintenance, inspection, standards development and worker training. The Handbook also discusses how the NESC Committee has interpreted the rules in the Code and responded to change proposals during the past 90 years. This allows users to understand how questions they may have were dealt with in the past. The Seventh Edition includes provisions for loading on warm island utility installations located between 25 degrees North and 25 degrees South latitudes and revised minimum approach distance requirements based upon recent research.

Ordering information and availability

Available in both printed and PDF file edition.