ASTM F2599-11

Standard Practice for The Sectional Repair of Damaged Pipe By Means of An Inverted Cured-In-Place Liner

ASTM International / 15-Dec-2011 / 3 pages

1.1 This practice covers requirements and test methods for the sectional cured-in-place lining (SCIPL) repair of a pipe line (4 in, through 60 in. ) by the installation of a continuous resin-impregnated-textile tube into an existing pipe by means of air or water inversion and inflation. The tube is pressed against the host pipe by air or water pressure and held in place until the thermo set resins have cured. When cured, the sectional liner shall extend over a predetermined length of the host pipe as a continuous, one piece, tight fitting, corrosion resistant and verifiable non-leaking cured-in-place pipe.

1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that provided for information only and are not considered standard.

1.3 There is no similar or equivalent ISO Standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Particular attention is drawn to those safety regulations and requirements involving entering into and working in confined spaces.

Keywords:
Sectional cured-in-place lining; tube; sheet; vacuum impregnate; continuous; bladder; textile; felt; knit; resin; inversion; inflation; ambient cure; steam cure; launcher; liner/bladder assembly; ICS Number Code 23.040.99 (Other pipeline components)

Ordering and availability

This publication is available both in printed and PDF edition.

BS PD 25888:2011

Business continuity management. Guidance on organization recovery following disruptive incidents

British Standards Institution / 31-Dec-2011 / 32 pages

Cross References:
PD 25111
BS EN ISO 9000
ISO/IEC Guide 73
Control of Substances Hazardous to Health Regulations 2002 (COSHH) as amended
Control of Major Accident Hazards Regulations 1999 (COMAH)
BS 25999-1:2006
BS 25999-2:2007

All current amendments available at time of purchase are included with the purchase of this document.

Keywords:
Management; Business continuity; Management operations; Commerce; Enterprises; Organizations ; Risk assessment; Risk analysis; Planning; Documents; Personnel; Records (documents); Insurance

Product Code(s): 30194308

Ordering and availability

This publication is available only in printed edition.

SAE AS 6124

Aluminum Axially Swaged Fittings, Installation and Inspection Procedure

SAE International / 20-Dec-2011 /

This procedure establishes the instructions to prepare tube ends, install and inspect axially swaged permanent tube fittings qualified to AS6116. This procedure is applicable when specified on the engineering drawing or in the procurement document.

Ordering and availability

This publication is available both in printed and PDF edition.

DIN 6868-162 – DRAFT

Draft Document – Image quality assurance in diagnostic X-ray departments – Part 162: R�V acceptance test of X-ray installations for digital mammography

Deutsches Institut Fur Normung E.V. (German National Standard) / 01-Jan-2012 / 50 pages

Ordering and availability

This publication is available both in printed and PDF edition.

NFPA (Fire) 115

Laser Fire Protection, 2012 Edition

National Fire Protection Association / 02-Jan-2012 / 27 pages

Work safely around lasers. Bring your knowledge in line with the latest guidelines in the 2012 NFPA 115.

NFPA 115: Laser Fire Protection provides criteria for the safe design, manufacture, installation, and use of lasers and associated equipment. It also contains recommended procedures for training and response to fire emergencies involving lasers.

Chapters cover:

  • Classification of lasers
  • Evaluation of laser beam ignition potential
  • Laser beam ignition
  • Fire safety requirements for laser equipment
  • Flammable gases
  • Reactive gases
  • Ignitible liquids used in laser systems
  • Operations and administration
  • Emergency preparedness

The Standard’s Annexes provide explanatory material and information on the nature of hazards, education and training, flash point, and more.

Ordering and availability

This publication is available only in printed edition.

PIP PNE00012

Piping Examination and Leak Testing Guide [Complete Revision]

Process Industry Practices / 01-Nov-2011 / 9 pages

: This Practice describes guidelines for specifying requirements for examination and leak testing of metallic, lined metallic, and nonmetallic piping systems designed in accordance with ASME B31.3 Process Piping Code. This Practice provides guidelines for specifying requirements for examination of piping materials, components, fabrication, assembly, and installation; and associated documentation. This Practice provides guidelines for the extent of examination, criteria for acceptance, and correction of defective work. This Practice describes the types of leak tests, bases for selecting the appropriate tests, and arrangements for testing piping.

Ordering and availability

This publication is available both in printed and PDF edition.

IEEE C57.148-2011

IEEE Standard for Control Cabinets for Power Transformers

Institute of Electrical and Electronics Engineers / 03-Jan-2012 / 48 pages

Requirements for the design and construction of control cabinets on power transformers.

Keywords:
cabinet,circuit,component,construction,control cabinet,controls,current transformer,design,IEEE C57.148,layout,manufacture

Product Code(s): STD97164,STDPD97164

Ordering and availability

This publication is available both in printed and PDF edition.

NFPA (Fire) 252

Fire Tests of Door Assemblies, 2012 Edition

National Fire Protection Association / 02-Jan-2012 / 21 pages

Evaluate the ability of of fire doors to resist the passage of flame, heat, and gases with the latest testing provisions in the 2012 NFPA 252.

Revised to include updated references, the 2012 NFPA 252: Standard Methods of Fire Tests of Door Assemblies outlines methods of fire testing door assemblies that testing laboratories and manufacturers can use to determine assembly suitability when fire resistance of a specific duration is required. The Standard allows different fire door assemblies to be compared with each other in order to evaluate their relative performance as measured against a standard fire experience.

Ordering and availability

This publication is available only in printed edition.