VDE 0830-7-5-1:2012-11 / DIN EN 50132-5-1:2012

Alarm systems – CCTV surveillance systems for use in security applications – Part 5-1: Video transmission – General video transmission performance requirements; German version EN 50132-5-1:2011 + AC:2012

Verband der Elektrotechnik Elektronik Informationstechnik e.V. / 01-Nov-2012 / 64 pages

This European Standard introduces general requirements on video transmission. A detailed specification on analog video transmission over different media including signal and performance requirements is already defined in prEN 50132-5-3. For the growing number of surveillance applications based on IP video transmission the requirements are defined in 2 standards.

Ordering and availability

This publication is available both in printed and PDF edition.

SCTE 29 2012

Torque Requirements for Bond Wire Penetration of Bonding Set Screw

Society of Cable Telecommunication Engineers / 23-Oct-2012 / 5 pages

This test procedure is to determine the mechanical force needed to penetrate bonding wire to the appropriate depth. Bonding wire penetration should be
25 +/-1% of wire O.D.

Ordering and availability

This publication is available both in printed and PDF edition.

AASHTO MEBC-1-UL

Manual for Emulsion-Based Chip Seals for Pavement Preservation, 1st Edition, Single User Digital Publication

American Association of State and Highway Transportation Officials / 2012 / 54 pages

This manual addresses the factors affecting chip performance, discusses design and construction considerations, and identifies procedures for selecting the appropriate chip seal materials. It provides highway agencies with the information necessary for designing and constructing long-lasting chip seals and preserving pavements. The material contained in the report should be of immediate interest to state maintenance engineers and others involved in the maintenance and preservation of flexible pavements.

Ordering and availability

This publication is available only in PDF edition.

ASTM D4652-05(2012)

Standard Specification for Silicone Fluid Used for Electrical Insulation

ASTM International / 15-Oct-2012 / 2 pages

1.1 This specification covers silicone fluid for use in transformers, capacitors, and electronic assemblies as an insulating or cooling medium, or both.

1.2 Silicone fluid covered by this specification is polydimethylsiloxane having a nominal viscosity of 50 cSt at 25°C and a fire point of 340°C or greater. This specification applies only to new silicone fluid. Information on in-service maintenance testing is available in appropriate guides.

Keywords:
electrical insulating liquid; silicone fluid;

Ordering and availability

This publication is available both in printed and PDF edition.

IEEE 577-2012

IEEE Standard Requirements for Reliability Analysis in the Design and Operation of Safety Systems for Nuclear Power Generating Stations

Institute of Electrical and Electronics Engineers / 19-Oct-2012 / 25 pages

Revision Standard – Active.
The minimum acceptable requirements for the performance of reliability analyses for safety systems when used to address the reliability considerations discussed in industry standards and guidelines are set forth in this standard. The requirement that a reliability analysis be performed does not originate with this standard. However, when reliability analysis is used to demonstrate compliance with reliability requirements, this standard describes an acceptable response to the requirements.

Keywords:
IEEE 577,nuclear facilities,reliability analysis,safety systems

Product Code(s): STD97288,STDPD97288

Ordering and availability

This publication is available both in printed and PDF edition.

SCTE 132 2012

Test Method For Reverse Path (Upstream) Bit Error Rate

Society of Cable Telecommunication Engineers / 23-Oct-2012 / 10 pages

This procedure defines a method of measurement for Bit Error Rate (BER) in the return path of active Cable Telecommunications equipment. It is intended for measurement of 75-ohm devices having type "F" or 5/8-24 KS connectors. See the Cable Telecommunications Testing Guidelines document, ANSI/SCTE 96 2003, for a discussion of proper testing techniques.

Ordering and availability

This publication is available both in printed and PDF edition.

IEC 61347-2-9 Ed. 2.0 b:2012

Lamp controlgear – Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps)

Edition: 2.0
International Electrotechnical Commission / 30-Oct-2012 / 61 pages

IEC 61347-2-9:2012 series specifies particular safety requirements for electromagnetic controlgear for discharge lamps such as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps. The standard covers inductive-type electromagnetic controlgear for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with discharge lamps, having rated wattages, dimensions and characteristics as specified in IEC 60188, IEC 60192 and IEC 60662. This second edition cancels and replaces the first edition published in 2000, Amendment 1:2003 and Amendment 2:2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) the addition of a new Clause 14;
b) the word "ballast" is changed to "electromagnetic controlgear".

This publication is to be read in conjunction withIEC 61347-1:2007.

Keywords:
61347-2-9

Ordering and availability

This publication is available both in printed and PDF edition.

SCTE 82 2012

Test Method for Low Frequency and Spurious Disturbances

Society of Cable Telecommunication Engineers / 23-Oct-2012 / 16 pages

To define and measure low frequency and spurious disturbances caused by switched mode power supplies or other active devices in broadband Cable Telecommunications equipment.

Ordering and availability

This publication is available both in printed and PDF edition.

ATIS 0800035.v002

Technical Report – Validation Process for IPTV Quality Measurements

Alliance for Telecommunication Industry Solutions / 01-Oct-2012 / 29 pages

This document discusses a proposed test process for IPTV Perceptual Quality Measurements. It describes the industry standards test process currently followed, indicates its shortcomings, and suggests solutions for the identified weaknesses. The proposed process is flexible and is believed to address market needs better than the current process.

Ordering and availability

This publication is available both in printed and PDF edition.

SAE AMS 4232C

Aluminum Alloy Extrusion 2.7Cu 2.2Li 0.12Zr (2090-T86) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated

SAE International / 25-Oct-2012

This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles.These extrusions have been used typically for parts in structural applications requiring strength similar to 7050-T6 alloy with good exfoliation resistance and with a lower density of approximately 7.8%, but usage is not limited to such applications.

Ordering and availability

This publication is available both in printed and PDF edition.