IEEE 1716-2014

IEEE Recommended Practice for Managing Natural Disaster Impact on Key Electrical Systems and Installations in Petroleum and Chemical Facilities

Published by: IEEE / 2014-08-12 / 25 pages
New IEEE Standard – Active.

Recommendations and guidelines for managing natural disaster impact on key electrical facilities and systems in petroleum and chemical facilities are provided in order to minimize economic damage by pre-assessment risk evaluation of electrical facilities, by identification of mitigation techniques and system designs to minimize impact, and by outlining procedures for faster recovery of electrical systems after a natural disaster.

Ordering and availability

This publication is available both in printed and PDF edition.

BS EN ISO 16443:2014

Dentistry. Vocabulary for dental implants systems and related procedure

Published by: British Standard / European Standard / International Organization for Standardization / 2014-07-31 / 40 pages

Cross References:
ISO 1942
DIN 13902-1
DIN 13902-2
DIN 13902-3
ISO 704
ISO 860
ISO 1087-1
ISO 10241-1

All current amendments available at time of purchase are included with the purchase of this document.

Ordering and availability

This publication is available both in printed and PDF edition.

UL 61010-2-032

Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-032: Particular requirements for hand-held and hand-manipulated current sens

Published by: Underwriters Laboratories / 2014-08-08
Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use – Part 2-032: Particular Requirements for Hand-Held and Hand-Manipulated Current Sensors for Electrical Test and Measurement
UL 61010-2-032 (IEC 61010-2-032:2012)1 Scope and object

This clause of Part 1 is applicable except as follows:
1.1.1 Equipment included in scope

Replacement:Replace the existing text with the following:

This part of IEC 61010 specifies safety requirements for HAND-HELD and hand-manipulated current sensors described below.

These current sensors are for measuring, detecting or injecting current, or indicating current waveforms on circuits without physically opening the current path of the circuit being measured. They may be stand-alone current sensors or accessories to other equipment or parts of combined equipment (see Figure 101). These include measurement circuits which are part of electrical test and measurement equipment, laboratory equipment, or process control equipment. The existence of these current sensors and circuits in equipment requires additional protective means between the current sensor, the circuit and an OPERATOR.

NOTE 1 This part includes also the requirements of Part 2-030. Testing and measuring circuits that are not within the scope of this part are considered to be covered by the requirements of Part 1 or other parts 2s of IEC 61010, and then will also need to meet the requirements of these other parts with the exception of Part 2-030. Current clamp meters and similar currents sensors that have a primary purpose of measuring voltage on a live MAINS CIRCUIT are also within the scope of Part 2-033.

NOTE 2 Some current sensors are also known as current clamps and current probes.

Current sensors require hand manipulation before or after a test or measurement, but do not necessarily need to be HAND-HELD during the test or measurement.NOTE 3 Some current sensors designed for portable use can also be used for fixed installations.

The following types of current sensors are covered:a) Type A: a current sensor designed to be applied around or removed from UNINSULATED HAZARDOUS LIVE conductors. Type A current sensors have defined HAND-HELD or hand-anipulated parts providing protection against electric shock from the conductor being measured, and also have protection against short-circuits between wires and busbars during clamping.b) Type B: a current sensor which has protection against short-circuits between wires or busbars during clamping but without defined HAND-HELD or hand-manipulated parts which provide protection against electric shock during clamping. Additional protective means are necessary to avoid electric shock from HAZARDOUS LIVE conductors which cannot be de-nergised during application or removal of the current sensor.

EXAMPLE 1 Flexible current sensors.

c) Type C: a current sensor without protection against short-circuits between wires or busbars during clamping. Type C current sensors are intended to be applied to or removed from UNINSULATED HAZARDOUS LIVE conductors or from non-limited-energy circuit conductors only when they are de-energised.

EXAMPLE 2 Split-core transducers.

d) Type D: a current sensor designed to be applied around or removed from insulated conductors or from limited-energy circuit conductors.

A Type D current sensor does not need protection against short-circuits during clamping and has no defined HAND-HELD or hand-manipulated parts providing protection against electric shock from the conductor being measured.EXAMPLE 3 Current probes for oscilloscopes and earth leakage current detectors.

NOTE 4 All current sensors can also be used around insulated conductors. In this case, HAZARDS are limited to acceptable levels by the insulation of the conductors.

Key1 JAW END(S)2 JAW3 measuring circuit TERMINALS
1.1.1 Figure 101 – Examples of current sensors and their parts
1.2.1 Aspects included in scope

Addition:Add the following two new paragraphs at the end of the subclause:

Requirements for protection against HAZARDS resulting from NORMAL USE and REASONABLY FORESEEABLE MISUSE of measuring circuits are given in Clause 101.

Requirements for prevention of HAZARD from arc flash and short-circuits are given in Clause 102.

Ordering and availability

This publication is available only in printed edition.

BS EN 2226:2014

Aerospace series. Steel X105CrMo17 (1.4125). Hardened and tempered. Hand and die forgings. De $3L 150 mm

Published by: British-Adopted European Standard / 2014-07-31 / 12 pages

Cross References:
EN 4258
EN 4500-003
EN 4700-006

All current amendments available at time of purchase are included with the purchase of this document.

Ordering and availability

This publication is available both in printed and PDF edition.

SAE AS6174A

Counterfeit Materiel; Assuring Acquisition of Authentic and Conforming Materiel

Published by: SAE International / 2014-07-29
This SAE Standard standardizes practices to: a. maximize availability of authentic materiel, b. procure materiel from reliable sources, c. assure authenticity and conformance of procured materiel, including methods such as certification, traceability, testing and inspection appropriate to the commodity/item in question, d. control materiel identified as fraudulent/counterfeit, e. and report suspect or confirmed fraudulent/counterfeit materiel to other potential users and Authority Having Jurisdiction.

Ordering and availability

This publication is available both in printed and PDF edition.

DIN EN 60384-14-2 – DRAFT

Draft Document – Fixed capacitors for use in electronic equipment – Part 14-2: Blank detail specification – Fixed capacitors for electromagnetic interference suppression and connection to the supply mains – Safety tests only (IEC 40/2286/CD:2014)

Published by: DIN-adopted European Standard / 2014-08-01 / 21 pages

Ordering and availability

This publication is available only in printed edition.

DIN 21773

Gears – Cylindrical involute gears and gear pairs – Inspection dimensions of tooth thickness

Published by: Deutsches Institut Fur Normung E.V. (German National Standard) / 2014-08-01 / 28 pages

Ordering and availability

This publication is available both in printed and PDF edition.

ASTM Volume 12.01:2014

ASTM Book of Standards Volume 12.01: Nuclear Energy (I)

Published by: ASTM International / 2014-08-01 / 1466 pages
Published annually in August.

This volume contains 175 standards.

These two volumes feature over 300 nuclear-related standards. Volume 12.01 focuses on materials for nuclear reactor applications and covers:

Fuel and Fertile Materials–details property requirements for fuel and other related subjects.

Nuclear Grade Materials–establishes standard procedures for chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of these materials.

Ordering and availability

This publication is available only in printed edition.

BS EN 61300-2-35:2014

Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Tests. Cable nutation

Published by: British-Adopted European Standard / 2014-08-31 / 18 pages

Cross References:
IEC 61300-3-1
EN 61300-3-1
IEC 61300-3-3
EN 61300-3-3
IEC 61300-3-4
EN 61300-3-4
IEC 61753-1
EN 61753-1

All current amendments available at time of purchase are included with the purchase of this document.

Ordering and availability

This publication is available both in printed and PDF edition.

BS EN ISO 2759:2014

Board. Determination of bursting strength

Published by: British Standard / European Standard / International Organization for Standardization / 2014-07-31 / 24 pages

Cross References:
ISO 186
ISO 187
ISO 536
http://www.techstreet.com/cgi-bin/joint.cgi/hraz/products/928655
ISO 5725-1
ISO/TR 24498
AS/NZS 1301-403s:1997
TAPPI T 807
TAPPI T 810
TAPPI T 1200

All current amendments available at time of purchase are included with the purchase of this document.

Ordering and availability

This publication is available both in printed and PDF edition.