Category Archives: ETSI EN

ETSI EN 301 025

VHF radiotelephone equipment for general communications and associated equipment for Class "D" Digital Selective Calling (DSC); Harmonised Standard covering the essential requirements of articles 3.2 and 3.3(g) of the Directive 2014/53/EU

Published by: 2017-02-01 / 2017-02-01 / 60 pages
ETSI EN 301 025 covers the minimum requirements for general communication for shipborne fixed installations using a VHF radiotelephone operating in certain frequency bands allocated to the maritime mobile service using either 25 kHz or 25 kHz and 12,5 kHz channels and associated equipment for DSC – class D.

These requirements include the relevant provisions of the ITU Radio Regulations, appendix 18 [1], Recommendations ITU-R M.493-13 [3] (where class D is defined), M.825-3 [i.4] and incorporate the relevant guidelines of the IMO as detailed in IMO Circular MSC/Circ-803 [i.1].

The present document also specifies technical characteristics, methods of measurement and required test results.

The present document contains requirements to demonstrate that “… Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference” [i.3] and that “….radio equipment supports certain features ensuring access to emergency services” [i.3].

In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Directive 2014/53/EU [i.3] may apply to equipment within the scope of the present document.

Ordering and availability

This publication is available both in printed and PDF edition.

ETSI EN 301 489-4

Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 4: Specific conditions for fixed radio links and ancillary equipment and services

Published by: 2017-02-01 / 2017-02-01 / 21 pages
ETSI EN 301 489-4, together with ETSI EN 301 489-1 [1], covers the assessment of Fixed Radio Links, and ancillary
equipment in respect of ElectroMagnetic Compatibility (EMC).

Technical specifications related to the antenna port of the radio equipment are not included in the present document.

Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for
Analogue and Digital Fixed Radio Links operating as fixed Point-to-Point, and Point-to-Multipoint systems as defined
in annex A, including the associated ancillary equipment.

Examples of Fixed Radio Links are given in annex A.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The processing and protection switch, (de)modulator, transmitter, receiver, RF filters, branching networks, feeders are
covered by the present document. The multiplexing and/or de-multiplexing elements are covered if they form part of the
transmitter, receiver and/or transceiver.

The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

Ordering and availability

This publication is available both in printed and PDF edition.

ETSI EN 301 908-11

IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 11: CDMA Direct Spread (UTRA FDD) Repeaters

Published by: 2017-01-01 / 2017-01-01 / 33 pages
ETSI EN 301 908-11 applies to the following equipment types: Repeaters for IMT-2000 CDMA Direct Spread (UTRA FDD). This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1.

Ordering and availability

This publication is available both in printed and PDF edition.

ETSI EN 302 194

Navigation radar used on inland waterways; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU

Published by: 2017-02-01 / 2017-02-01 / 56 pages
ETSI EN 302 194 specifies technical characteristics and methods of measurements for equipment:

  • 1) X band Radar and its associated primary navigational display intended for the navigation of vessels on inland
    waterways subject to the requirements of the Central Commission for the Navigation on the Rhine (CCNR)
    and the Danube Commission (DC).

The present document contains the minimum technical, operational and functional requirements, describes the tests and
the conditions under which the tests take place in order to establish that the equipment meets these minimum
requirements.

Additional facilities, which may be provided on this equipment, e.g. Inland ECDIS functions, automatic steering
functions or additional interfaces, are not covered by the present document, and other appropriate standards may apply.

The installation of radar equipment intended for the navigation on inland waterways is subject to additional conditions
which are described in annex E.

Ordering and availability

This publication is available both in printed and PDF edition.

ETSI EN 303 132

Maritime low power VHF personal locating beacons employing Digital Selective Calling (DSC); Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU

Published by: 2017-03-01 / 2017-03-01 / 34 pages
ETSI EN 303 132 lays down the minimum requirements for low power maritime personal locating beacons
employing DSC signalling according to ETSI EN 300 338-6 [1], on the VHF maritime mobile frequency band channel 70.
Maritime personal locating beacons employing DSC signalling also include AIS with an integrated GNSS receiver to
provide the locating function according to ETSI EN 303 098 [2]. The present document incorporates the relevant
provisions of the International Telecommunication Union (ITU) radio regulations [i.4] included in Recommendation
ITU-R M.493-14 [3]. The present document does not cover requirements for the integrated GNSS receiver providing the
locating function.

LBT (Listen Before Talk) techniques are employed to improve spectrum efficiency.

For this application, both the radiated power and the length of time of operation are limited to enable the equipment to
be sufficiently small and light to be worn comfortably at all times and to limit the operating range to a local area.

The present document also specifies technical characteristics, methods of measurement and required test results.

The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.

Ordering and availability

This publication is available both in printed and PDF edition.

ETSI EN 303 360

Satellite Earth Stations and Systems (SES); Satellite broadcast reception equipment; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Outdoor unit receiving in the 10,7 GHz to 12,75 GHz frequency band

Published by: 2017-02-01 / 2017-02-01 / 24 pages
ETSI EN 303 360 specifies technical characteristics and methods of measurements for the following type of
equipment:

  • Radar equipment for obstacle detection for rotorcraft use fitted with integral antennas operating in the
    frequency range from 76 GHz to 77 GHz and references CEPT/ERC/ECC Recommendation 70-03 [i.1],
    Annex 5 and Commission Decision 2006/771/EC [i.2] as amended.

  • Short Range Devices (SRD) intended for the use on board rotorcrafts with the application to detect obstacles.

Ordering and availability

This publication is available both in printed and PDF edition.

ETSI EN 300 392-7

Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 7: Security

Published by: 2017-01-01 / 2017-01-01 / 216 pages
ETSI EN 300 392-7 defines the Terrestrial Trunked Radio system (TETRA) supporting Voice plus Data (V+D). It
specifies the air interface, the inter-working between TETRA systems and to other systems via gateways, the terminal
equipment interface on the mobile station, the connection of line stations to the infrastructure, the security aspects in
TETRA networks, the management services offered to the operator, the performance objectives, and the supplementary
services that come in addition to the basic and teleservices.

The present part describes the security mechanisms in TETRA V+D. It provides mechanisms for confidentiality of
control signalling and user speech and data at the air interface, authentication and key management mechanisms for the
air interface and for the Inter-System Interface (ISI).

Clause 4 describes the authentication and key management mechanisms for the TETRA air interface. The following two
authentication services have been specified for the air-interface in ETR 086-3 [i.3], based on a threat analysis:

  • authentication of an MS by the TETRA infrastructure;
  • authentication of the TETRA infrastructure by an MS.

Clause 5 describes the mechanisms and protocol for enable and disable of both the mobile station equipment and the
mobile station user’s subscription.

Air interface encryption may be provided as an option in TETRA. Where employed, clause 6 describes the
confidentiality mechanisms using encryption on the air interface, for circuit mode speech, circuit mode data, packet data
and control information. Clause 6 describes both encryption mechanisms and mobility procedures. It also details the
protocol concerning control of encryption at the air interface.

The present document does not address the detail handling of protocol errors or any protocol mechanisms when TETRA
is operating in a degraded mode. These issues are implementation specific and therefore fall outside the scope of the
TETRA standardization effort.

The detail description of the Authentication Centre is outside the scope of the present document.

Ordering and availability

This publication is available both in printed and PDF edition.

ETSI EN 300 338-5

Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 5: Handheld VHF Class H DSC

Published by: 2017-02-01 / 2017-02-01 / 43 pages
ETSI EN 300 338-5 states the minimum requirements for general communication for handheld VHF radios using the
handheld class H DSC for shipborne use.

Class H DSC may be used in the Very High Frequency (VHF) Maritime Mobile Service (MMS), for distress, urgency
and safety communication and general communications using telephony for subsequent communications.

The present document is part 5 of a multi-part deliverable that covers the requirements to be fulfilled by equipment that
is integrated with a handheld transceiver.

These requirements include the relevant provisions and the guidelines of the IMO as detailed in MSC/Circ.803 [i.1] for
non-SOLAS vessels participating in the GMDSS.

Ordering and availability

This publication is available both in printed and PDF edition.

ETSI EN 300 422-2

Electromagnetic compatibility and Radio spectrum Matters (ERM); Wireless microphones in the 25 MHz to 3 GHz frequency range; Part 2: Harmonized EN under article 3.2 of the R&TTE Directive

Published by: 2017-02-01 / 2017-02-01 / 63 pages
ETSI EN 300 422-2 applies to equipment operating on radio frequencies between 25 MHz and 3 GHz, using
analogue, digital and hybrid (using both analogue and digital modulation) modulation.

The present document applies to the following radio equipment types:

  • Professional Wireless Microphone Systems (PWMS);
  • in ear monitoring systems;
  • consumer radio microphones;
  • tour guide systems; and
  • Assistive Listening Devices (Aids for the handicapped) comprising personal and public hearing aid systems.

The maximum power recommended for equipment covered by the present document is 250 mW for radio microphones
and 500 mW for public hearing aids in the 169,4 MHz to 169,8125 MHz band (erp below 1 GHz and eirp above
1 GHz).

The present document also covers radio microphones used in the 863 MHz to 865 MHz band, with a maximum power
of 10 mW.

Ordering and availability

This publication is available both in printed and PDF edition.

ETSI EN 301 091-3

Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices; Road Transport and Traffic Telematics (RTTT); Radar equipment operating in the 76 GHz to 77 GHz range; Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive

Published by: 2017-02-01 / 2017-02-01 / 23 pages
ETSI EN 301 091-3 specifies technical characteristics and methods of measurements for the following types of
equipment:

  • radar equipment for obstacle detection applications in the frequency range from 76 GHz to 77 GHz at the road
    crossing of a railway track and references CEPT/ECC ERC Recommendation 70-03 [i.1] Annex 4;

  • Short Range Devices (SRD) intended for the use at road crossing of a railway track.

Ordering and availability

This publication is available both in printed and PDF edition.