BS DD CEN/TS 15548-1:2011

Thermal insulation products for building equipment and industrial installations. Determination of thermal resistance by means of the guarded hot plate method. Measurements at elevated temperatures from 100 degreesC to 850 degreesC

British Standards Institution / 31-Dec-2011 / 28 pages

Cross References:
EN 1946-2
EN 12664
EN 12667:2001
EN 12939
EN ISO 7345
EN ISO 9288
ISO 9288:1989
ISO 8302:1991

All current amendments available at time of purchase are included with the purchase of this document.

Keywords:
Thermal insulating materials; Thermal insulation ; Construction materials; Buildings; Industrial ; Thermal resistance; Thermal conductivity; Thermal testing; High-temperature testing; Temperature measurement; Test equipment; High temperatures

Product Code(s): 30153921

Ordering and availability

This publication is available only in printed edition.

SAE J 2223-3

Connections for On-Board Road Vehicle Electrical Wiring Harnesses~Part 3: Multipole Connectors~Flat Blade Terminals~Dimensional Characteristics and Specific Requirements ( Stabilized: Dec 2011 )

SAE International / 20-Dec-2011 /

This document has been declared "Stabilized" and will no longer be subjected periodic reveiws for currency. Users are responsible for verifying references and continued suitability of technical requirements. Newer technology may exist.This SAE Standard defines dimensional characteristics of existing flat blades of multipole connectors and specific requirements for on-board electrical harnesses of road vehicles.This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance only.

Ordering and availability

This publication is available both in printed and PDF edition.

ASTM B228-11a

Standard Specification for Concentric-Lay-Stranded Copper-Clad Steel Conductors

ASTM International / 15-Nov-2011 / 4 pages

1.1 This specification covers bare concentric-lay-stranded conductors made from bare round copper-clad steel wires for general use for electrical purposes.

1.2 For the purpose of this specification, conductors are classified as follows: Grade 40 HS, Grade 30 HS, and Grade 30 EHS.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Keywords:
clad steel electrical conductor; concentric-lay-stranded copper-clad steel electrical conductor; copper-clad steel electrical conductor; copper electrical conductor<char: emdash>copper-clad steel; copper electrical conductor<char: emdash>stranded; electrical conductor; Concentric-lay-stranded copper electrical conductors; Copper-clad steel electrical conductors–specifications; Steel wire (copper processed)–specifications; Stranded copper electrical conductors–specifications ; ICS Number Code 29.060.20 (Cables)

Ordering and availability

This publication is available both in printed and PDF edition.

PIP CVI02350

Roadway and Area Paving General Notes and Typical Details [Complete Revision & Renumbering of CVI02000]

Process Industry Practices / 01-Oct-2011 / 31 pages

This Practice provides typical details for construction of roadways and area paving for use in conjunction with design drawings and project specifications.

This Practice provides typical details for roadway paving, area paving, guard posts, guard rails and headwalls. General notes are provided to supplement the requirements shown on design drawings and project specifications. Area paving details are for 4- and 6-inch concrete paving intended for pedestrian and light vehicular traffic. Abbreviations commonly used on design drawings are also listed in this Practice.

Ordering and availability

This publication is available both in printed and PDF edition.

ANSI/ASSE A10.8-2011

Safety Requirements for Scaffolding

American Society of Safety Engineers / 13-Feb-2012 / 126 pages

This standard establishes
safety requirements for the construction,
operation, maintenance and use of scaffolds
used in the construction, alteration,
demolition and maintenance of buildings
and structures. This standard does not
cover permanently installed suspended
scaffold systems or aerial platforms.

To purchase the Comparison Document of A10.8-2001 and A10.8-2011 together with the current standard, click on "Buy Redline."

Ordering and availability

This publication is available both in printed and PDF edition.

SAE ARP 6178

Fraudulent/Counterfeit Electronic Parts; Tool for Risk Assessment of Distributors

SAE International / 20-Dec-2011 /

This SAE Aerospace Recommended Practice is applicable for all organizations that procure electronic components from sources other than the original component manufacturer of the component. It is especially applicable for assessing distributors that sell electronic components without contractual authorization from the original component manufacturer

Ordering and availability

This publication is available both in printed and PDF edition.

ASTM D2950/D2950M-11

Standard Test Method for Density of Bituminous Concrete in Place by Nuclear Methods

ASTM International / 01-Dec-2011 / 5 pages

1.1 This test method describes a test procedure for determining the density of bituminous concrete by the attenuation of gamma radiation, where the source and detector(s) remain on the surface (Backscatter Method) or the source or detector is placed at a known depth up to 300 mm [12 in.] while the detector or source remains on the surface (Direct Transmission Method).

1.2 The density, in mass per unit volume of the material under test, is determined by comparing the detected rate of gamma emissions with previously established calibration data.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements see Section 6 and Note 4.

Keywords:
bituminous-concrete density; density; in-place density; nuclear test method; Concrete; Density–paving materials; Gamma radiation–soil/rock; Neutron radiation–concrete; Nuclear methods; ICS Number Code 93.080.10 (Road construction); 93.080.20 (Road construction materials)

Ordering and availability

This publication is available both in printed and PDF edition.

CAN/CGSB 3.5-2011

Essence automobile

Canadian General Standards Board / 13-Dec-2011 / 36 pages

La présente norme s'applique à quatre qualités d'essence sans plomb ni phosphore qui sont destinées à être utilisées dans des moteurs à allumage commandé sous diverses conditions climatiques.

Ordering and availability

This publication is available both in printed and PDF edition.

NFPA (Fire) 287

Test Methods for Measurement of Flamability of Materials in Cleanrooms Using a Fire Propagation Apparatus, 2012 Edition

National Fire Protection Association / 02-Jan-2012 / 35 pages

Evaluate the fire risk of materials and products containing polymers to determine their suitability for use in cleanrooms based on the 2012 NFPA 287.

Revised to include updated references, the 2012 NFPA 287: Standard Test Methods for Measurement of Flammability of Materials in Cleanrooms Using a Fire Propagation Apparatus (FPA) addresses methods for measuring the flammability characteristics of materials containing polymers that are used in cleanroom applications.

NFPA 287 is associated with a large-scale, self-sustained upward or flow-added fire propagation on materials and products. Measurements include:

  • Critical heat flux
  • Thermal response parameter
  • Fire propagation index
  • Effective heat of combustion
  • Smoke yield

TheStandard is essential for testing laboratories and manufacturers that want to reduce fire dangers in cleanrooms.

Ordering and availability

This publication is available only in printed edition.

ASME, ASTM, ANSI, ISO, CSA, API… all the news