Tag Archives: SAE AMS

SAE AMS4782G

Nickel Alloy, Brazing Filler Metal 71Ni – 10Si – 19Cr 1975 DEGREES F (1080 DEGREES C) Solidus, 2075 DEGREES F (1135 DEGREES C) Liquidus

Published by: 2017-03-28 / 2017-03-28 / 5 pages
SAE AMS4782G covers a nickel alloy in the form of wire, rod, strip, foil, and powder and a viscous mixture (paste) of the powder in a suitable binder.

Ordering and availability

This publication is available both in printed and PDF edition.

SAE AMS03_4A

The Pre-Treatment and Protection of Steel Items of Specified Maximum Tensile Strength Exceeding 1450 MPa (Stabilized: Mar 2017)

Published by: 2017-03-21 / 2017-03-21 / 19 pages
SAE AMS03_4A specifies the special treatments and precautions that are to be observed when protective and other surface treatments are applied to items, including springs, made from steel of specified maximum tensile strength exceeding 1450 MPa. The requirements of this Standard qualify those in process specifications and override the latter where there is conflict. The Standard also gives advice on design, manufacture, and preparation of items prior to cleaning and protection.

Ordering and availability

This publication is available both in printed and PDF edition.

SAE AMS4939C

Titanium Alloy Sheet, Strip, and Plate 3Al – 8V – 6Cr – 4Mo – 4Zr Solution Heat Treated

Published by: 2017-03-28 / 2017-03-28 / 8 pages
SAE AMS4939C covers a titanium alloy in the form of sheet, strip, and plate through 4.000 inches (101.60 mm) nominal thickness.

Ordering and availability

This publication is available both in printed and PDF edition.

SAE AMS4079H

Aluminum Alloy, Drawn, Round, Seamless, Tubing 1.0Mg – 0.60Si – 0.28Cu – 0.20Cr (6061-O) Close Tolerance, Annealed

Published by: 2017-03-14 / 2017-03-14 / 6 pages
SAE AMS4079H covers an aluminum alloy in the form of drawn, round, seamless tubing with wall thickness of 0.018 to 0.500 inch (0.46 to 12.70 mm), inclusive (see 8.5). This tubing has been used typically for ducts requiring small radius bends and moderate strength after solution and precipitation heat treatment, but usage is not limited to such applications.

Ordering and availability

This publication is available both in printed and PDF edition.

SAE AMS2808E

Identification Forgings (Stabilized: Mar 2017)

Published by: 2017-03-28 / 2017-03-28 / 4 pages
SAE AMS2808E covers the requirements for identification of forgings, including die forgings, hand
forgings, and rolled rings.

Ordering and availability

This publication is available both in printed and PDF edition.

SAE AMS5339G

Steel, Maraging, Investment Castings, 17Ni – 10Co – 4.6Mo – 0.30Ti – 0.06Al, Vacuum Melted, Homogenized, Overaged, and Solution Heat Treated

Published by: 2017-03-24 / 2017-03-24 / 11 pages
SAE AMS5339G covers an alloy steel in the form of investment castings.

Ordering and availability

This publication is available both in printed and PDF edition.

SAE AMS03_1A

Impregnation of Porous Castings & Sintered Metal Components (Stabilized: Mar 2017)

Published by: 2017-03-21 / 2017-03-21 / 8 pages

This SAE Standard specifies the processes and type of impregnant which can be used when impregnating castings for the following purposes:

a. For the recovery of ferrous and non-ferrous castings containing micro porosity, where pressure tightness is mandatory.

b. For sealing castings/sinter metal components to improve corrosion resistance and/or to render the surface suitable for subsequent surface treatment.

Ordering and availability

This publication is available both in printed and PDF edition.